HOW TO: CHANGING TAPS
TO COMPLETE THIS PROJECT YOU WILL NEED...
• Flexible/copper connectors
• Kitchen Taps
• Pipe cutter
• Power Drill (cordless)
• PTFE tape
• Torch
• Universal Spanner
• Backing Plates
• Fibre washers
• Tap Extenders
• Top-hat Washers
• Basic Plumbing
• Fit a Bath & Wash Basin
• Fit a Toilet & Bidet
INTRODUCTION
Changing taps can give a new lease of life to a bathroom suite or kitchen, and modern fittings make the job a lot
easier than it used to be.
The most difficult part is removing old taps which, in bathrooms, may be puttied in. On a workbench it would be a
fairly easy job but the inaccessibility makes it awkward, so don't rush into it. Invest a little time in getting
comfortable, and you will work faster with less strain. Get a good light so you can see exactly what you are doing
and, if you have to lie on your back, use a cushion for your head.
SKILL LEVEL
Basic plumbing skills would be useful. Good agility and dexterity are essential to work in cramped conditions.
SAFETY FIRST
Ensure all metal pipes and the bath (if metal) are bonded to a common earth. Take care when using a blowlamp.
Keep naked flames away from flammable material. Make sure that the water is off and well drained before
placing a lead lamp near the underside of the taps. If possible, use a water-resistant double-insulated lamp.
When working upside down, wear eye protection.
2 - GETTING STARTED
Make sure you turn the water off properly before you begin. Once the old taps
are out, things become easier because you can use new, user-friendly fittings.
If you are fitting new taps at the same time as fitting a new sink or bath, it is
easier to fit the taps before you put the sink/bath in place. Sometimes you
can attach whole sections of pipework as well.
Not all taps are suitable for British-style low-pressure systems which use a
tank in the loft. So check before buying. Continental taps are made for
mains pressure. If you have an unvented water cylinder or combination
boiler, then Continental taps should work well. If you have a tank in the loft,
it is best to stick to British-made taps.
3 - SERVICE VALVES
Tap connectors can be substituted for integral service valves to provide an
easy means of shutting off the water. The top end fits onto the tap and the
bottom end is a compression fitting for the pipe. The valve can be turned off
for re-washering and servicing the tap
If access is difficult, use Speedfit hand-tightenable tap connectors with
integral 'O' rings. The pipe pushes into the end of the fitting once it has been
screwed onto the tap. Fibre washers can be held in place by wrapping a few
turns of PTFE tape around them and the top of the connector. This also
helps make a better seal.
4 - PRELIMINARY CHECKS
New taps are all made to standard dimensions, but check the hole distances
in old baths or sinks, as they aren't always compatible with mixer taps.
Mixer-tap holes for baths should be approximately 180mm (7.25in) apart,
and 195mm (7.75in) apart for sinks. If they aren't standard, you will need to
buy adjustable union taps with swivels.
Check that the spout is long enough to deliver water into the bath or basin
without dribbling over the side. If you have an old bath with non-standard
tap-hole centres, you can buy a mixer with adjustable cranked swivel tails.
Alternatively, fit individual taps.
You may also find that the holes in a basin, sink or bath are square (set like
diamonds). A new smaller bodied tap doesn't always cover the hole. The only
way around this is to buy some chrome cover plates and put them on first.
Some bath taps are connected directly to lead pipes with a wiped joint. The
lead can be cut back to a straight section and joined with a special
mechanical fitting. Don't try to solder copper fittings on to the lead. Where
the lead goes back to a galvanized-iron pipe, it will be easier to unscrew the
lead completely and use new flexible tails or lengths of plastic pipe.
If you want to fit a bath/shower mixer, make sure that both the existing taps
are fed from the low-pressure tank-fed system. A quick check can be made
by turning on the tap and holding your thumb over the end immediately. If
the pressure pushes your thumb off it is most likely to be a mains-fed tap.
5 - REMOVING OLD TAPS
Turn off the water and drain the pipes through the taps. If possible, open
other taps lower on the system to drain any remaining water in the pipes.
Check that the water is completely shut off - it isn't easy or pleasant to work
with water still dribbling through the pipes.
Use a claw spanner to undo the tap connectors and back nuts on the
underside of the sink, bath or basin. If the taps begin to turn, get
somebody to hold them with a wrench or block of wood.
You can cut a notch in a piece of wood and use it as a lever to hold the taps
steady. Alternatively, mark two holes where the spouts are positioned and
drill two holes so the piece of wood can be slipped over both spouts to hold
the taps steady.
Remove old taps and the complete waste fitting if the new taps incorporate a
pop-up waste.
If the taps won't budge, it is often easier to cut through the brass back-nut
with a hacksaw, and then prise the nut open with an old screwdriver. When
this is impossible due to lack of space, the taps can be drilled from the top.
Select a drill of the same diameter as the back-nut under the tap. This will
be a 3/4in drill for a 1/2in basin or sink tap or a 1in drill for a 3/4in bath tap.
Remove the whole of the head-work and carefully drill straight down through
the body of the tap. Be careful that the drill doesn't snag. It is best to use a
drill with torque control if you aren't sure you can hold it.
Don't try turning basin taps in their holes while you hold the back-nut steady
or you might damage the china or enamel.
Undo the head mechanisms of taps before fitting and check the inside is
free of swarf. A surprising number of new taps contain debris which can
damage 'O' rings and washers.
6 - FITTING NEW TAPS
Single taps sometimes twist when they are turned off. They should have
anti-rotation washers to hold them steady. Alternatively, you can bed the
taps in silicone sealant and let the whole assembly dry for 24 hours.
Clean the area around the taps. If the bath is metal and there are signs of
rust, use a rust remover before fitting the taps. Fit the new taps by placing
them through the hole with the rubber anti-rotation washer on the upper
side. Hot goes on the left, cold on the right.
It is easier to reach the far tap under a bath if you unscrew the overflow pipe
from the hole in the bath. Remember to replace it afterwards.
Place a plastic top-hat spacer washer (if fitting to a thin sink) on the
underside and hand-tighten the back nuts. Hold the tap steady and tighten
the back nuts with a wrench or box spanner.
If the old pipework fits, you can use it, but replace the fibre washers in the
tap connectors. If the old pipes don't fit, or are awkward, it is easier to cut
the pipes back and fit new connectors.
The easiest connectors to fit are the braided flexible type. Make sure they
have rubber or fibre washers in them before you screw them on.
Single-hole mixers have fairly flexible copper tails. You can bend them
slightly but don't try bending them any more than 45 degrees or you will kink
the pipe. The tails are easier to connect because they are longer, and you
can see what you're doing. Use compression fittings or push-fit fittings to
join the pipework to the taps.
Two-hole mixer taps need to be sealed above the bath or sink with the
special washers provided. Check the holes are a standard distance apart.
Connect the tap end of flexible connectors before attaching them to the
supply pipes.
Flush pipes through with the taps open before closing them off. If a tap
doesn't shut off properly, don't force it or you will damage the washer or
disc. Open it up fully, run the water and then close it again. This should clear
any debris.
7 - THREE-HOLE BASIN AND BIDET MIXERS
Assembling a three-hole mixer is done by placing each section through the
holes in the basin or bidet and connecting the pipes underneath.
Full instructions come with the tap.
8 - FINAL CHECKS
If you get a leak there is always a reason,
so don't try to force the nut on further than it
should go. It is better to turn off the water and
undo the fitting so you can see exactly where
the problem lies. Examine the surfaces of the
metal and look closely at the sealing washers.
Check the pipes are squarely aligned and
screw the tap connectors back on. You should
find this does the trick!
For lots more information please Visit http://www.ideg.co.uk
Read more at: . |
Home Repair 
